Lỗi out of paper canon lbp151 ufrii lt
|
Nguyên nhân gây ra lỗi "paper out" của máy in hầu như là do khay giấy của máy in đã sử dụng hết giấy hoặc máy in không thể rút được giấy trong khay,... hoặc do một số nguyên nhân khác. Để tìm hiểu và khắc phục tình trạng này, sửa máy in tại nhà Cần Thơ Linh Khôi Luân mời bạn tham khảo bài viết bên dưới để biết được các cách xử lý khi máy in hiển thị lỗi này nhé. Show Trong quá trình in, máy xuất hiện thông báo lỗi “Out of Paper”. Điều này có nghĩa là máy hết giấy hoặc không rút được giấy trong khay. Có rất nhiều nguyên nhân khác nhau dẫn đến lỗi này. Nhận biết lỗi out of paperĐể nhận biết lỗi này rất đơn giản, thông thường khi in sẽ xuất hiện hộp thoại xử lý lệnh in. Trong quá trình in nếu có lỗi máy tính sẽ hiện thông báo lỗi để người dùng dễ khắc phục. Trong trường hợp này sẽ có thông báo máy in bị lỗi out of Paper. Kèm theo đó là hướng dẫn với dòng “Load A4 paper in Manual Feed“. Có nghĩa là bạn cần phải cho giấy A4 vào khay giấy Manual Feed Slot – hiện tại đang không còn giấy. Các cách sửa lỗi "paper out" cực đơn giảnKiểm tra giấy trong khayKéo khay ra và kiểm tra xem giấy còn hay đã hết. Nếu giấy bị ẩm, rách hoặc cong nên thay bằng giấy mới. Ngoài ra, hãy đảm bảo rằng các giấy tờ có chiều dài và loại chính xác. Căn chỉnh các cạnh của tờ giấy đồng đều và đặt nó trở lại vào khay. Kiểm tra mặt sauNắp của máy in ở phía sau có thể không được đóng. Xoay thiết bị xung quanh và kiểm tra đã đóng kín chưa. Nếu nó không được đóng hoàn toàn, có thể có giấy kẹt ở đó. Nếu vậy, mở nắp và lấy giấy bị kẹt ra khỏi máy. Tắt nguồnTrước hết, rút dây nguồn mà không cần tắt nguồn máy in. Sau đó, đợi 30 giây trước khi cắm lại máy in. Trong trường hợp máy in không tự động bật, hãy nhấn vào nút nguồn thủ công. Bụi, vụn giấy hay các mảnh vụn khác sẽ khiến cho con lăn không còn hoạt động chuẩn như ban đầu. Làm sạch con lănBụi bẩn tích tụ trong con lăn của nó có thể dẫn đến lỗi nạp giấy. Làm sạch và tắt máy in trước khi thao tác. Sử dụng một miếng vải không xơ để làu chùi. Khi bạn đã hoàn tất việc vệ sinh để khô một lúc trước khi bật nguồn. When printing from an application with which you cannot set the paper size and paper type, the document is printed with the paper size and paper type set here. When printing with Google Cloud Print, the paper type setting here is applied. Mobile Print Paper Size Custom X: 76.2 mm to 216.0 mm Y: 127.0 mm to 356.0 mm A4 Envelope DL Envelope C5 Letter Legal Statement Executive Foolscap Oficio Envelope No. 10 (COM10) Envelope Monarch Letter (Government) Legal (Government) Legal (India) Foolscap (Australia) Oficio (Brazil) Oficio (Mexico) 3x5inch Paper Type Plain (60-89 g/m2) Plain L (60-89 g/m2) Recycled (60-89 g/m2) Color (60-89 g/m2) Heavy 1 (90-120 g/m2) Heavy 2 (121-163 g/m2) Envelope Bond 1 (60-90 g/m2) Bond 2 (91-120 g/m2) Bond 3 (121-163 g/m2) Index Card Labels Log on to the Remote UI () [Paper Size] Specify the paper size when printing from a mobile device. If [Custom] is selected, you can specify any value for width and length. [Paper Type] Specify the paper type when printing from a mobile device. Display SettingsSelect the display units and language for the Remote UI. Millimeter/Inch Entry Millimeter Inch Remote UI Language English Korean Portuguese Spanish Log on to the Remote UI () [Millimeter/Inch Entry] Select the unit of measurement for the Remote UI screens. [Remote UI Language] Select the display language used for the Remote UI screens. Timer SettingsSpecify date and time settings, including the date format and the 12- or 24-hour clock display setting. The date and time that are printed on each report and list are determined by these settings. Date Format MM/DD/YYYY DD/MM YYYY YYYY MM/DD Time Format 12 Hour (AM/PM) 24 Hour Current Date Current Time Time Zone (UTC-12:00) International Date Line West to (UTC) Coordinated Universal Time Use Daylight Saving Time Off On Start January to March 1st to Last Monday to Sunday End January to October 1st to Last Monday to Sunday Auto Sleep Time After 1 min. After 5 min. After 10 min. After 15 min. After 30 min. Log on to the Remote UI () [Date Format] Select the date format (order of year, month, and day). [Time Format] Select the 12- or 24-hour clock display setting. [Current Date/Time Settings] Set the current date and time. [Time Zone] Set the time zone of the region where the machine will be used. [Use Daylight Saving Time] Enable or disable daylight saving time. If daylight saving time is enabled, specify the dates from which and to which daylight saving time is in effect. [Auto Sleep Time] The machine enters sleep mode automatically when it remains idle for a certain length of time. Specify the length of time until the machine enters auto sleep. We recommend using the factory default settings to save the most power. Common SettingsSpecify this setting when you print a document on paper with logos. To print on paper with logos, you need to change how the paper loaded in the paper source is facing depending on whether you are performing 1- or 2-sided printing. However, if you change the setting to [Print Side Priority], you can just load paper in the same way (which side up or down) both for 1- and 2-sided printing (the logo side face up when using the drawer, or the logo side face down when using the multi-purpose tray). For more information, see . Switch Paper Feed Method Multi-Purpose Tray Speed Priority Print Side Priority Drawer 1 Speed Priority Print Side Priority Log on to the Remote UI () [Speed Priority] When using paper that has been preprinted with a logo, you need to change how it is facing when you perform 1-sided and 2-sided printing. We recommend selecting [Speed Priority] if you do not need to consider which side to print on. [Print Side Priority] To print on a specific side of paper, you do not need to flip over paper in the paper source whether 1- or 2-sided printing is selected. If [Print Side Priority] is set for a paper source that is loaded with paper you cannot use for 2-sided printing (), [Speed Priority] is applied to the paper source instead. In this case, you need to load the paper in the same way as when [Speed Priority] is selected (). 1-sided printing speed may be slower when [Print Side Priority] is selected. Printer SettingsSpecify basic printing settings and PCL printing settings. Custom SettingsSpecify basic printing settings. Copies 1 2-Sided Printing Off On Action When Paper Size Mismatch Force Output Display Error Paper Default Paper Size A4 A5 B5 Envelope DL Envelope C5 Letter Legal Statement Executive Envelope No. 10 (COM10) Envelope Monarch 3x5inch Print Quality Density 17 Levels Toner Save Off On Layout Binding Location Long Edge Short Edge Timeout Timeout 5 Mobile Print Settings Halftones Gradation Error Diffusion Other Special Print Mode Off Special Settings 1 Special Settings 2 Log on to the Remote UI () [Copies] Set the number of copies to print. [2-Sided Printing] Select whether to make 2-sided printouts. [Action When Paper Size Mismatch] Select whether to go ahead with printing or to display an alert when the paper size that is loaded in the paper source and that specified in the printer driver are different. [Default Paper Size] Use this item to specify the paper size. [Density] Adjust the toner density. [Toner Save] You can save toner consumption. Select when you want to check the layout or other appearance characteristics before proceeding to final printing of a large job. [Binding Location] If you are binding the printouts with a binding tool such as a stapler, use this item to specify whether to bind on the long or short edge. [Timeout] Set the time period after which the current print job is automatically canceled in the case of a print data reception interruption. [Halftones] Select the image processing when printing from a mobile device with Mopria™, etc. Select [Gradation] for photos and illustrations, and [Error Diffusion] for mostly text documents for more attractive printouts. [Special Print Mode] In instances such as when a printed barcode is difficult to read, or text and image outlines are partially not printed, these problems may be improved by changing the setting of this option. If this option is set to [Special Settings 1], printing is at a lower density compared to when set to [Off]. Text and lines may also be faint. Images may also be partially not printed if this option is specified when printing on paper other than thin paper. If this option is set to [Special Settings 2], printing is at a lower density compared to when set to [Off] or [Special Settings 1]. Text and lines may also be faint. PCLSpecify the PCL printing settings such as page layout and print quality. Resolution 600 dpi 1200 dpi Density Fine Adjustment -1 to 0 Paper Save Off On Orientation Portrait Landscape Font Number 0 Point Size 4.00 to 12.00 Pitch 0.44 to 10.00 Form Lines 5 to 64 Character Code PC8 ROMAN8 ISOL1 ISOL2 ISOL5 ISOL6 PC775 PC8DN PC850 PC852 PC8TK PC1004 WINL1 WINL2 WINL5 WINBALT DESKTOP PSTEXT LEGAL ISO4 ISO6 ISO11 ISO15 ISO17 ISO21 ISO60 ISO69 WIN30 MCTEXT MATH8 MSPUBL PIFONT PSMATH VNINTL VNMATH VNUS Set Custom Paper Off On Unit of Measure Millimeters Inches X dimension 76.2 to 216.0 Y dimension 127.0 to 356.0 Append CR to LF Yes No Enlarge A4 Print Width Off On Halftones Text Resolution Gradation Color Tone Graphics Resolution Gradation Color Tone Image Resolution Gradation Color Tone Log on to the Remote UI () [Resolution] Specify the resolution to be used for print data processing. [Density Fine Adjustment] Adjust the toner density. This setting is enabled when [1200 dpi] is set in [Resolution]. [Paper Save] Specify whether to output blank pages, if any in the print data. [Orientation] Select [Portrait] (vertical orientation) or [Landscape] (horizontal orientation) for the page orientation. [Font Number] Specify the font to use by selecting a corresponding font ID number. You can print the PCL font list with font samples from the Printer Status Window. [Point Size] Set the font size in points, adjustable in 0.25 increments. You can specify this setting only when a proportionally-spaced scalable font is selected in [Font Number]. [Pitch] Set the font pitch, or cpi (characters per inch), adjustable in 0.01 increments. You can specify this setting only when a fixed-pitch scalable font or a bitmap font is selected in [Font Number]. [Form Lines] Set the number of lines printed on one page from 5 to 128. This setting is automatically changed according to the settings specified in [Default Paper Size] and [Orientation]. [Character Code] Select the character code that is most suited for the computer you send print data from. The specified setting is ignored when the character code is controlled by the font specified in [Font Number]. [Set Custom Paper] Select whether to set a custom paper size. Select [On] to set the dimensions of the paper in [X dimension] and [Y dimension]. [Unit of Measure] Select the unit of measurement to use to set a custom paper size. [X dimension] Specify the horizontal dimension (short edge) of the custom paper. [Y dimension] Specify the vertical dimension (long edge) of the custom paper. [Append CR to LF] Select whether to append a carriage return (CR) when the machine receives a line feed code (LF). If [Yes] is selected, the print position moves to the beginning of the next line when the machine receives an LF code. If [No] is selected, the print position moves to the next line, just under the received LF code. [Enlarge A4 Print Width] Select whether to expand the width of the printable area of A4 size paper in portrait orientation to that of LTR size. [Halftones] You can select the printing method to reproduce halftones (the intermediate range between the lighter and darker areas of an image) for optimal image quality. For each document, you can make settings by type of image. System ManagementYou can specify that a PIN (system manager password) is required when logging in to the Remote UI in System Manager Mode, and you can register information about the system manager, such as name and contact information. You can also register a name to identify this machine, and register its location. System Manager Information Set System Manager PIN Off On Set/Change PIN System Manager Name Contact Information E-Mail Address System Manager Comment Device Information Device Name Location Support Link Consumables Supplier Information Purchase From E-Mail Address URL Specification Method Select Country/Region Country/Region Custom URL Display Button for Purchasing Consumables Off On USB Device Settings Use as USB Device Off On Product Extended Survey Program Settings Use Product Extended Survey Program Off On PDL Selection (Plug and Play) Network UFR II LT UFR II LT (V4) PCL6 USB UFR II LT UFR II LT (V4) PCL6 Log on to the Remote UI in System Manager Mode ()
|
